Step Tutorial for Bathtub Installation
Step Tutorial for Bathtub Installation
Blog Article
What're your beliefs about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is additionally a reasonably tough task. If the old bathtub is easily available, the project can relocate immediately; if you have to open a wall to remove the old tub and position the new tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. See to it you have qualified on your own for the job and also are comfortable attempting it. Instead of working with a contractor to take control of a halfway-completed task, it is much better to take into consideration using one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This article will certainly assist you install a new tub in your bathroom if you have already gotten a brand-new tub and also don't need to alter the plan of your previous water supply pipes.
Your tools and material checklist must make up the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any water staying in the system. The process of eliminating the existing faucets can be fairly troublesome because of the limited gain access to that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the staying water that will originate from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning during this process. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to carrying on to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers are in location between the tap and the sink. Protect the faucet in place with the manufacturer offered backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The former type must be attached to the faucet finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the tub in the required setting. The wood boards are handy in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub till the level reads level.
To set up taps, fit the bottom of the outermost adaptable tap adapter to the ideal supply pipe by making a compression sign up with; then do the exact same for the other tap.
Switch on the water and inspect all joints and also brand-new pipework for leakages and tighten them if essential. Load the bath tub and also check the overflow outlet and also the regular outlet for leakages.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub ought to wait till the tub has actually been utilized at least when as this will certainly settle it right into its last position.
Planning for the Installation
To start with, the supporting structure supplied with the bath must be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the tub is in usage. The sealer can crack relatively early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid reader on Tools You Need to Install a New Bathtub , I think sharing that excerpt was valuable. Liked our piece? Please share it. Let another person check it out. I thank you for reading our article about How to Install a Bathtub.
We're here 24/7, call! Report this page